共找到 150 條與 機械漿 相關的標準，共 10 頁
1. OBJET 1.1 La présente norme s'applique au papier de pate mécanique couché offset utilisé pour l'impression offset, recto verso. Ce
Offset coated mechanical pulp paper
本標準規定了闊葉木堿性過氧化氫機械漿的產品分類、要求、試驗方法、檢驗規則及標志、包裝、運輸、貯存。本標準適用于以闊葉木(80%以上)為主要原料的堿性過氧化氫機械漿
Hardwood alkaline peroxide mechanical pulp
The document specifies the various maximum usable widths for entry and delivery sections of a warp sizing machine
Textile machinery - Warp sizing machines - Maximum usable width (ISO 6176:1994)
本標準規定了漿紗機輸入和輸出部分的最大有效寬度。本標準適用于漿紗機，漿絲機、漿染聯合機、整漿并聯合機也可參照使用
Textile machinery-Warp sizing machines-Maximum usable width
本標準規定了機械漿實驗室濕解離的儀器及試驗步驟。 本標準適用于各種機械漿(即機械漿、半化學漿和化學機械漿
Pulps.Laboratory wet disintegration.Disintegration of mechanical pulps
Cancels and replaces the first edition (1981). Specifies the various maximum usable widths for the entry and delivery sections of a warp sizing
Textile machinery - Warp sizing machines - Maximum usable width
Versione in lingua italiana della norma europea EN 643 (edizione maggio 1994). Stabilisce una nomenclatura delle qualita' normate europee di
List of european standard qualities of waste paper.
質量要求 質量要求應符合表 1規定。 表1 未漂白秸稈生物化學機械漿質量要求 指標名稱
Unbleached straw biochemimechanical pulp—Part 1: Pulp
1???Scope This document specifies an apparatus and the procedures for the laboratory wet disintegration of mechanical pulps that exhibit
Pulps. Laboratory wet disintegration. Disintegration of mechanical pulps at ≥ 85°C
本標準規定了磺化化學機械漿系統能量平衡和熱效率計算的原則和方法。 本標準適用于制漿造紙企業為掌握磺化化學機械漿系統熱量消耗狀況及熱平衡測試、計算等
Calculation method of energy balance and thermal efficiency of sulfonated chemical mechanical pulp (SCMP) system
Pulps－Laboratory wet disintegration－ Part 3：Disintegration of mechanical pulps at ≥85 ℃
4 磨漿設備 磨漿設備采用盤式磨機或錐型磨機磨漿。 化學處理及磨漿在常壓或帶壓(小于等于0.6 MPa)下進行。 磨片應選用少切斷、分絲帚化及細纖維化的齒型。建議齒寬1.2 mm～1.8 mm、槽寬1.6 mm～2.9 mm、齒高
Unbleached straw biochemimechanical pulp—Part 2:Technical specifications for refining
Pulps－Laboratory wet disintegration－ Part 3：Disintegration of mechanical pulps at ≥85 ℃
Pulps — Laboratory wet disintegration — Part 2 : Disintegration ofmechanical pulps at 20 °C
This part of ISO 5263 specifies an apparatus and the procedures for the laboratory-wet disintegration of mechanical pulps that do not exhibit latency
Pulps - Laboratory wet disintegration - Part 2: Disintegration of mechanical pulps at 20 degrees C (ISO 5263-2:2004)
